An SMD slide switch is a surface-mount slide switch that sets a fixed state, such as a power path, mode, or channel, and holds it mechanically with no firmware. Engineers choose it when a design needs a manual setting on a dense board built for automated assembly. Selection comes down to pole and throw, position count, actuator height and travel, reflow and wash compatibility, and the current rating, which on most compact slides is signal level rather than power. Swiclick builds SMD and through-hole slide switches in SPDT, DPDT, and multi-position formats, including the SPDT MSK12D03-TG2-NS-01 and the DPDT MSS22D05-TG2-MB1. Send your footprint, position count, target actuator height, voltage, current, and load type, and we will confirm the closest part.
What an SMD Slide Switch Is Good At
A slide switch keeps its position after you set it, which makes it right for settings that should not change on their own. Typical uses include power-source selection, mode setting, channel selection, and region configuration. Surface mounting removes plated-through switch terminals and supports automated assembly. Depending on the package and anchor tabs, it may also reduce total board and enclosure space. The trade is feel and reach: the low actuator profile and specified operating force affect how the switch feels through the enclosure, so panel access needs planning.
Poles, Throws, and Position Count
Start with how many circuits you switch and how many settings you need. A single pole, double throw (SPDT) slide moves one common line between two positions. A double pole, double throw (DPDT) slide moves two isolated lines together, useful for a power path plus a status line. Multi-position slide switches provide three or more selectable states. Swiclick covers the common cases: the SPDT slide switch MSK12D03-TG2-NS-01 (1P2T, 8.8 × 2 × 4.9 mm, non-shorting, 140 ± 50 gf, contact resistance ≤ 100 mΩ), the compact 2-position MSS22C07-TG2-MB1, and the DPDT slide switch MSS22D05-TG2-MB1 (2P2T, 9.1 × 3.5 × 5.5 mm, 12 V DC / 100 mA, 150 ± 50 gf, contact resistance ≤ 100 mΩ, SMD 6 terminals).
Actuator Height, Travel, and Feel
The actuator sets the user experience. A taller actuator is easier to reach through a slot but stands prouder on the board; a low actuator saves height but may require a tool or a closely fitted external slider. Match actuator height and travel to the enclosure opening before you commit, and confirm that the specified operating force gives a positive but usable switching feel. This is where a switch that meets every electrical spec still feels wrong in the product.
Reflow and Wash vs IP Sealing
Two process facts decide whether an SMD slide survives your line. First, the reflow profile: confirm the part is rated for your peak temperature and profile so the housing does not distort, the same discipline you apply when you read an SMD tact switch reflow profile. Second, cleaning: an open-frame slide can trap flux and wash water, so if the board is cleaned, specify a process-washable or sealed variant. Sealing options may be available within the wider Swiclick slide-switch range, but washability and environmental sealing must be confirmed for the exact part number. Keep two ratings separate: a process-washable switch is not automatically IP-rated for field exposure, and an IP-rated product is not automatically approved for every cleaning process. A non-shorting switch also prevents adjacent contacts from overlapping during transition, which matters when two sources, rails, or signal paths must never be connected together.
Ratings Run Low for a Reason
Most compact SMD slides are rated at signal level, for example 12 V DC at 100 mA, not for switching power. That is expected and is why they suit logic, mode, and channel selection rather than motor or lamp loads. If the design needs to switch a real load, confirm the rating against the datasheet rather than assuming, because compact contacts and terminals limit current and arc-handling capacity.
Matching an SMD Slide Footprint
Swiclick is the switch brand of Wenzhou Gangyuan Electronics Co., Ltd., with ISO 9001 certified production. The fastest way to a match is your footprint and target actuator height: send those with your position count, voltage, current, and load type, and we will confirm the closest SMD slide part and flag where the footprint or actuator differs from your current one.
FAQ
SMD means surface-mount device: the switch solders onto the board surface in a reflow line rather than through drilled holes, which suits automated assembly.
Usually not. Most compact SMD slides are rated at signal level, for example 12 V DC at 100 mA. Confirm the current rating on the datasheet before switching any real load.
An SPDT slide moves one common line between two positions. A DPDT slide moves two isolated lines together, which suits switching a power path and a status line at the same time.
Use a non-shorting (break-before-make) part when two sources, rails, or signal paths must never overlap during transition. Shorting types are fine where a brief overlap is acceptable.
No. Process-washable means it tolerates PCB cleaning; IP-rated means it is sealed against field exposure. Confirm the exact rating you need, because one does not imply the other.
The minimum order is 500 pieces with free 1 to 50 pc samples. Send your footprint and position count and we will confirm the part and lead time.