For OEM production, Swiclick offers the G10-1-00P-150-1056 as a candidate alternative to the Omron D2F-01F. The D2F-01F is an ultra subminiature pin plunger basic switch with a maximum operating force of 0.74 N or 75 gf, making operating force one of the key parameters to verify during second source qualification.
The Swiclick G10 candidate should not be treated as an automatic pin to pin replacement. PCB footprint, plunger position, operating force, terminal geometry, electrical rating and required mechanical life should be compared against the exact D2F-01F configuration before production approval.
For a broader model comparison, see our Omron Micro Switch Cross Reference. For the complete qualification workflow, review our Switch Second Source Solutions.
How D2F-01F Differs From Other D2F-01 Variants
Confirm the exact Omron model before selecting an alternative because actuator type and operating force change between variants.
D2F-01 uses a pin plunger with a maximum operating force of 1.47 N or 150 gf.
D2F-01F also uses a pin plunger but is the lower operating force version with a maximum operating force of 0.74 N or 75 gf.
D2F-01L uses a hinge lever and has a maximum operating force of 0.78 N or 80 gf.
D2F-01FL combines the hinge lever with the lower operating force configuration and has a maximum operating force of 0.25 N or 25 gf.
These values follow Omron’s current D2F datasheet. Always confirm the exact suffix and terminal configuration before qualification.
If your design uses the D2F-01L hinge lever version, see our Omron D2F-01L Alternative page.
Omron D2F-01F to Swiclick Cross-Reference
| Parameter | Omron D2F-01F | Swiclick G10-1-00P-150-1056 (what to verify) |
| Type | Sub-miniature snap-action | Sub-miniature snap-action (footprint-compatible, minor PCB adjustment) |
| Actuator | Pin plunger | Confirm plunger height against your mechanism |
| Cross-reference status | reference part | Candidate alternative; minor PCB adjustment may be required |
| Operating force | 0.74 N max. / 75 gf max. | may differ; confirm force profile against your application, do not assume a match |
| Terminals | through-hole | verify solder process compatibility |
| Validation | reference part | free sample (1 to 50 pieces, 4-day delivery) before production |
The Swiclick G10-1-00P-150-1056 is a candidate alternative for the Omron D2F-01F, but final suitability depends on the actual PCB, actuator geometry, operating force, electrical load and life requirement. Validate the candidate in the real application before releasing it to production.
What to Verify Before Replacing a D2F-01F
A cross reference should be evaluated against measurable parameters rather than a single compatibility percentage. For the D2F-01F, the most important checks are PCB terminal layout, plunger position, operating force, pretravel and overtravel, contact rating and required operating life.
Omron specifies a maximum operating force of 0.74 N for the D2F-01F, together with defined travel and operating position characteristics. Compare those values directly with the proposed Swiclick model and your mechanical design before approving the alternate.
A sample can confirm basic fit and function, but production qualification should also consider dimensional and electrical consistency across multiple lots.
What a Single Sample Cannot Confirm
A single engineering sample can confirm basic PCB fit, actuation and electrical function, but it cannot demonstrate production consistency.
For an OEM second source, review operating force distribution, contact resistance, critical dimensions and mechanical performance across representative production lots. If the switch is used at low signal levels, contact resistance stability should also be evaluated under the actual circuit conditions.
The qualification objective is not simply to find one sample that works. It is to confirm that the approved specification can be reproduced consistently during production.
How to Qualify in Three Steps
- Confirm that the existing part is the D2F-01F pin plunger version and record the terminal type, operating force requirement, load and mechanical dimensions.
- Compare the Swiclick G10-1-00P-150-1056 datasheet and drawing against the existing design, then request samples for application testing.
- Document any PCB, mechanical or electrical differences and complete the required validation before releasing the alternate to production.
For larger OEM qualification programs, see our Switch Second Source Solutions.
Why Swiclick
Swiclick supports OEM and EMS customers evaluating G series micro switches as alternatives and second sources for existing designs. Production is managed under ISO 9001 and IATF 16949 quality systems, while applicable product approvals and model specific documentation should be confirmed for the exact switch being qualified.
For the complete G series and other snap action configurations, review our Micro Switch product family.
The Swiclick G10-1-00P-150-1056 can be evaluated as a candidate alternative to the Omron D2F-01F. PCB fit, operating force, actuator geometry, electrical rating and required life should be validated before production use.
Omron specifies a maximum operating force of 0.74 N or 75 gf for the D2F-01F pin plunger model.
The D2F-01F is a pin plunger model with a maximum operating force of 0.74 N. The D2F-01L uses a hinge lever and has a maximum operating force of 0.78 N. The actuator geometry means they require different replacement evaluation.
It should not be treated as an automatic drop in replacement. Compare the PCB footprint, terminal geometry, actuator position, operating force, electrical rating and life requirement, then validate samples in the actual application.