Which Omron Micro Switches Can Swiclick Match?

Cross-referencing an Omron micro switch means finding an equivalent from another maker that fits the same footprint and meets the same load, then verifying the differences before committing a board. In practice, most cross-brand matches for parts like the D2F, SS, and V series are footprint-compatible alternatives that need minor PCB adjustment, not pin-to-pin drop-ins, and some Omron variants, particularly the high-life versions rated for tens of millions of operations, often cannot be matched at all. An honest cross-reference says which is which, instead of labeling everything a drop-in.

Swiclick is a switch manufacturer offering G-series snap-action micro switches as alternatives to common Omron basic and subminiature switches. The table below grades each cross-reference from Swiclick’s own data: which models cross over at roughly 70–95% with minor PCB adjustment, and which Swiclick does not claim to replace.

How to read this cross-reference

Each row is graded three ways, because not every Omron part has an honest equivalent:

• ✓ Cross-references (≈70–95%, minor PCB adjustment). A footprint-compatible Swiclick part covers the function with small board changes. Suited to cost-sensitive designs where Omron’s highest-spec variants are not required.
• ✗ Not replaceable. Swiclick does not offer an equivalent, usually a high-life or specialized variant. Listed honestly rather than left blank.
• Case-by-case. Families with too many variants to map generically; confirm per model.

The percentage is a starting estimate from Swiclick’s cross-reference data, not a guarantee. Use the validation guides linked in section ⑥ to confirm rating, contact configuration, terminals, mechanical fit, and certifications against your exact part.

Omron → Swiclick cross-reference

Have a part number that is not in this table? Send it and Swiclick will check it against the G series and say plainly whether it cross-references, needs a custom variant, or cannot be matched.

What “70–95%, minor PCB adjustment” actually means

It means the Swiclick part covers the same function and footprint closely enough to design in, but is not a guaranteed pin-to-pin swap. Small board changes, such as pad spacing, a terminal variant, or a lever length, may be needed to fit it exactly, and the part suits designs where Omron’s tightest spec or highest life rating is not a hard requirement. Saying 70–95% rather than “100% drop-in” is deliberate: anyone promising a blanket drop-in across brands, without reading both datasheets, is selling optimism. The honest range is what lets you plan the small rework up front instead of finding it after the first build.

When Swiclick cannot match it

Some Omron parts are marked “not replaceable” above, and that is the point of an honest cross-reference. High-life variants (10M+ operations) and a few specialized models are outside what Swiclick offers, and the table says so rather than overselling. When a part you need is not a stock match, Swiclick runs a defined process instead of forcing a fit:

• Confirm the requirement and the real operating conditions.
• Run an R&D feasibility analysis.
• Within about 30 working days, provide a sample proposal, drawing, and test report that states the differences plainly.
• Agree a tooling cost based on volume, where a custom variant is the right answer.
• If a genuine physical or technical barrier prevents a match, say so clearly and recommend the closest functional alternative.

A supplier that will tell you “this one we cannot match” is the one worth trusting on the parts it can. The “not replaceable” rows are not a weakness in this table; they are the reason the “✓” rows are credible.

How to validate a cross-reference

A grade in the table is the starting point. Before you design a Swiclick part in, confirm the four things that decide whether any cross-brand switch actually drops into your circuit:

• Electrical rating, including the inductive load figure: see the guide to reading a micro switch’s inductive rating and the “16(6)A” parenthetical.
• Contact configuration: matching NO, NC, and COM (SPST vs SPDT).
• Terminals: solder, quick-connect, and PCB, and how to match them.
• Mechanical fit and operating force: matching mounting, lever, force, and travel.
• Certifications: matching UL, TÜV, and ENEC for your market.

Request a sample or a cross-reference check

Swiclick’s G-series micro switches are certified to UL, ENEC (ENEC-01613), and TÜV Rheinland under an ISO 9001 quality system, with free samples in 4 days (1–50 pieces) and datasheets available without a form.

Whether you are designing a part in or qualifying Swiclick as a second source against Omron, the honest grade up front keeps the program on schedule. Send the Omron part number you are replacing and the real load and conditions, and an application engineer will return the cross-reference, the honest replaceability grade, and the matching G-series part against the datasheet.

FAQ